Well, picking it up tomorrow excited a tad 🤣👍

Quick clean it's so nice to drive its unreal:)

Ordered some backbox delete pipes, black grill and vents and glohh gl-3 rear lights. I wasnt too keen on the smoked ones tho prefered the indicators.... not 100% sure about these and may sell them on if I dont like them.
Also black lettering front and rear
Ohh and installed some smoked/clear side indicators as one of mine was cracked/full of condensation.

I must say, mostly town driving with the odd run we are over 30mpg which I was shocked at, I am driving a lot slower than I used to but still... very happy

nice....will be interested to see the lights

Yes. I will upload pics and keep this thread as a car diary I think for my own reference and so people can see the differences

Right.... loads of parts came today but its wet and I cant do the lettering.

New grill, side vents, rear lights are on Took 30 mins or so for the lot. Heres some before and after pics..... found a bag behind the first vent - thought I had struck white gold hahahahaha anyone know what they are?

Ohhh also I did the 9 clicks of the seatbelt with ignition on, engine not running to turn off the seatbelt moaning noise. Much nicer

I need to do this,

Have you been tweaking endlessly the reverse dip position? I have!  RRS TDV8 HSE 2008 - Tip Top and new to me atm

No hahaha I am 6 2 so can reach.... the wife is short tho
Wait, I meant boot lid position..... reverse dip as in mirrors? Yeah I set them once haha

Front....

Rear.... bit spoiled by my poor phone edit skills.... and yes, n and g need replaced as somehow I got them slightly squint 🙄

Just a point, how easy is it to replace the letters? I'd like to change to black on my tailgate but I am one of those that gets upset at any kind of misalignment so if it was visibly out, I'd be twitching every time I looked at it. RRS HSE Dynamic SDV6 2014

Nemo mortalium omnibus horus sapit

As you can see by mine, I failed haha - I will change the 2 letters asap tho as I am the same.
You get a stencil, unfortunately mine didnt line up very well - possibly a bad stencil. I think the foam was distored/stretched.
The front one was VERY easy.

Steps were....
1- give it a wash, save scratching.
2- put on stencil and mark corners/top and bottom with masking tape.
3- remove stencil.
4- use the wifes hair drier and a credit card type device to peel off stickers - I used my work ID card
5- remove worst of glue by rubbibg thumb.
6- use t-cut or polish to remove final glue.
7- stick stencil back in place.
8- stick new letters on.

The only 1 I had issues with was the rear range rover one, I expect it will be fine when I order a couple new letters but it is a pest it happened.... at the end of the day it will be worth it

....just ordered another rear set. I will just do all of the " range "

these guys have loads of badge removal videos

Bertbuckie wrote:

As you can see by mine, I failed haha - I will change the 2 letters asap tho as I am the same.
You get a stencil, unfortunately mine didnt line up very well - possibly a bad stencil. I think the foam was distored/stretched.
The front one was VERY easy.

Steps were....
1- give it a wash, save scratching.
2- put on stencil and mark corners/top and bottom with masking tape.
3- remove stencil.
4- use the wifes hair drier and a credit card type device to peel off stickers - I used my work ID card
5- remove worst of glue by rubbibg thumb.
6- use t-cut or polish to remove final glue.
7- stick stencil back in place.
8- stick new letters on.

The only 1 I had issues with was the rear range rover one, I expect it will be fine when I order a couple new letters but it is a pest it happened.... at the end of the day it will be worth it

....just ordered another rear set. I will just do all of the " range "